FP-100 Flush Pin Adapter

Specifications: 1″-14 NF thread allows mounting in Model 10 Dow-Gage or TACOMP Stub. Adapter pin is O-1 tool steel; RC60-63, .250 dia. slide fit in body with spherical radii ground on both ends. Tempered spring steel clip retains flush pin tooling (Standard Flush Pin Blanks or customized Educated Flush Pin Gages) in place.

This product can be customized to suit your gaging requirements.

Standard Flush Pin Blank

Specifications: Bodies are hardened RC60-62, ground, lapped and black oxide finished. Body dia. is knurled 1-3/16″ with a marking flat. Body length is 1-1/4″. Pins are 0-1 tool steel; RC60-63, ground and lapped slide fit in body and held in place with a set screw. Overall pin length is 3-1/4″. Available in the following pin diameters: 1/4″, 5/16″, 3/8″, 7/16″ and 1/2″.

This product can be customized to suit your gaging requirements.

Standard Stage Set

Specifications: Bodies are hardened RC60-62, ground, lapped and black oxide finished. Pins are O-1 tool steel; RC60-63, ground and lapped slide fit in bodies. Pins are 3-1/2″ overall length with a ground spherical radius on one end. Bodies have a 1-3/8″ dia. gaging surface. Available in the following pin diameters: 1/4″, 5/16″, 3/8″, 7/16″ and 1/2″.

This product can be customized to suit your gaging requirements.

Standard LS-Platen

Specifications: Bodies are C1117 steel; case hardened RC60-62, ground, lapped and black oxide finished. Bodies are available with 2″, 3″, 4″ or 5″ diameter gaging surfaces. Pins are 0-1 tool steel; RC60-63, ground and lapped slide fit in body. Pins are 3-1/2″ overall length with a ground spherical radius on one end. Available in the following pin diameters: 1/4″, 5/16″, 3/8″, 7/16″ and 1/2″.

This product can be customized to suit your gaging requirements.

GA-15 Stage Blank

Specifications: Made of C1117 steel (soft) with 1″-14 NF 2 thread. GA-15 Stage Blank is 2-5/8″ overall length with 1-3/8″ dia. working surface. Recommended heat treatment, pack harden RC60-62, .040″ case depth.

This product can be customized to suit your gaging requirements.

Standard Gage Pins

Specifications: Material is O-1 drill rod hardened to RC60-63. Pins are available in the following decimal sizes ground to a tolerance of +/- .0001″ (.2500, .3125, .3750, .4375 & .5000). Pins are 3-1/2″ overall length with a ground spherical radius on one end.

This product can be customized to suit your gaging requirements.

ANSI/AGD Group 2 (Mahr Federal & L.S. Starrett Dial Indicators)

Specifications: (Dial approx. 2-1/4″ dia.) Available in inch and metric models. Vertical lug back and standard 1/4″ contact point.

Mahr Federal Micro Maxum II

Specifications: Inductive Digital Electronic Indicator.
Provides both digital and analog readout with digital output. Operator selectable inch/metric settings. Preset capabilities. Auto power down for longer battery life. Furnished with vertical lug back for ANSI/AGD mounting.

Mahr Federal Micro Maxum III

Specifications: Digital Electronic Indicator features both digital display and fan analog display. User configurable in inch/metric units, normal reverse sensing, resolution, analog scale, and tolerance setup & display.

Starret Model 2900

Specifications: Provides both digital and analog readout with digital output.

Operator selectable inch/metric settings.

Preset capabilities. Auto power down for longer battery life. Furnished with vertical lug back for ANSI/AGD mounting.